Showing posts with label Mistral Moth. Show all posts
Showing posts with label Mistral Moth. Show all posts

Tuesday, May 29, 2018

Another New Mistral hits the water

Back in March of 2014 UK sailor Dominic Bowns contacted me about Mistral plans.  Earlier this week he sent me photos of the completed boat.  Dominic's rate of progress makes John Z. seem speedy.  The first two photos are courtesy of Dominic.  The last three are ones I found on the International Moth FB page.  Looks like she was worth the wait.  Dominic indicates that now his business partner wants one...










Wednesday, December 23, 2015

The finish line

Today I received this photo of Martin Scott's Mistral Evolution.  It's nice to see one of the two Mistrals which I've been posting about actually make it to the water!  John Z: are you listening?!

Martin Scott and Evolution.  Martin not only built the boat but designed the sail as well.  Although the sail is a bit smaller than that permitted by the IMCA it still measures in as legal. Note the full length battens are confined to the top of the sail.  Well done Martin!

Friday, April 17, 2015

Sail Ho!

Since we last heard, Martin Scott has been busy on his computer designing a sail for Evolution.  The sail is a bit smaller than the max permitted by the IMCA-UK but Martin thinks he'll be faster if the boat stays sunny side up.  I agree, capsizing is not at all fast.  Martin gave his computer file to a local sail maker and what we see in the following three photographs is how the sail looks on an old tapered Needlespar mast which Martin has in his collection of boat stuff.  Martin is thinking about adding an extra batten between the top batten and batten Nr 2.  At this point He estimates that the boat has cost roughly $2400 US dollars to build and it appears that he's very nearly done.  Martin hopes to launch her this May.  The cost compares favorably against that of a new Laser or Aero don't you think?

Martin has recently ordered a set of Shelley Mk III plans for a friend.  If the narrow Shelley is built with hiking wings, as designed, and equipped with a modern IMCA shaped sail as seen here, it will be a very interesting comparison when the boats go head to head on the race course.  These two designs couldn't be more different if they tried: the Mistral is a narrow waterline, round bilge shape, while the Shelley is a wedge which, with the right skipper, is capable of planing up wind.



Looks good to me.  Martin says that the software he uses for sail design tells one the total amount of cloth required, including allowing for the seams, and then computes the total size of the finished sail.  He temptingly tells me that his design could be scaled down to Classic Moth size.  Hmmm.

Monday, March 30, 2015

Getting closer

Further progress from Martin Scott:  Paint and varnish.  I love the shape of the Mistral design from this angle.



Wednesday, December 10, 2014

More Deckage.

No sooner had I updated John Z's progress than I received some new photos from Martin Scott over in Cornwall.  I may need to start a pool to see which of these two Mistrals will be launched first...

Fore deck temporarily held in place during initial fitting with duct tape.


Looks good!  Note the neatness of both the boat and the work area.  Martin is building his boat in the utility room of his house, while John Z. builds in his downstairs rec room!  I don't know how they do it!

Martin's boat will have a center main traveler.  John is planning to stick with an aft bridle.

Martin is also designing his own sail.  He indicates that although he'll be measured under the IMCA's current rules, he will build a slightly less powerful sail than is permitted in the interests of controlling the boat in his local conditions.

Friday, December 5, 2014

John Z. Mistral update: The decks are on.

John's Mistral now has her decks.  All of the key seams have been glass taped (I learned that vacuum bagging flattens the selvaged edges of glass tape, so there are no little annoying ridges to sand down).

The decks have two coats of epoxy but have not yet been varnished.The diagonal lip at the aft edge of the side decks demarcates the seating areas where John used thicker plywood.

At this stage the hull weighs 57 pounds.  John has plenty of leeway for rub rails, hardware, hiking straps, varnish, etc. in order to get the boat up to the class minimum weight of 75 pounds.  He intends to make several test coupons to predict weight gain with different weights and types of glass cloth to help decide whether or not to sheath the exterior of the hull.

A look at the neatly done fore deck joint around the mast tube.  A nice dark mahogany streamlined boss surrounding the mast tube might look nice.

Plenty of access ports in the well deck and main bulkhead.  The cockpit sole has a 3mm ply doubler in the "stomping area".  John may add a layer of fiberglass to provide a non-skid texture to the sole.

Wednesday, October 15, 2014

Further updates from Martin Scott

Last week, just after seeing the latest pix of John Z's Mistral, I rec'd an update from Martin
Scott:

"I still have some fairing of the  keel band, but I have done 4 coats of International Schooner varnish, thinned 50-50 on the hull outside. The mast supports are all sound. I sailed with semi unstayed rigs with my Solo - however the waves and surf knock all the energy out - I prefer to sail with about 250 lbs of rig tension. So I am going to deck step the mast. I am working on a sail plan which is between your traditional plan, 15ft luff 9 ft foot. and (the IMCA) fully battened sail." Martin indicated that his sail will have a 16ft luff with an 8ft foot three battens the top full length). "My local Sailmaker who makes Transat Yacht sails has an apprentice and we are all working together with the computer design."

"I have laminated the carlins for the cockpit edge and have found a nice shape which should work well. I have make a removable thwart for light airs."

"Full  side tanks rolled to the floor allows the boat to float too high and blow away in our big seas. This is why I have have chosen to do tanks beside the plate box and I will be making a false floor just aft of the CB box for about 9ins and three ins deep. I also enclose a picture which illustrates the final gunwale configuration. The deck goes on followed by 3mm of sycamore then a mahogany finish. This will give a nice drop to either side of the side deck. I hope this is on interest to you as from next week things will slow up!
Kind regards to you all, Martin"
And now for Martin's pix:
Evolution is looking very smart.  As he indicated in his email, Martin continues to fair the keel line of his hull.

This pix shows the hardwood blocks which will be mounting points for various bits of hardware installed once the decks are on.  The clamps seen in the photo hold the deck carlins in place until the glue dries.

A close up of the gunwale.

I'll be very interested to see the details of the removable thwart Martin mentioned.  With very narrow waterlines, Mistrals are rather tedious to sail in light air so a thwart to comfortably sit on would be an advantage, especially if it could easily be removed and stowed if the breeze piped up.  Compare Martin's internal structure with that in John Z's Mistral.

John's boat will have a keel stepped, semi-free standing mast while Martin has opted to go with the more conventional deck stepped mast, supported by standing rigging.

Tuesday, September 9, 2014

Martin's building jig

Further pix from Martin's Mistral build.  These show the details of his building jig for those who are contemplating a Mistral building project for the coming winter months.

The empty building jig.

Gusset details.


The jig with the hull stably in place.

The original instructions which are part of the Mistral plans provide no details of how to pull up the boat without twisting or other misshape anomalies.  The plans just indicate that you should pull up the two hull skin panels around the main bulkhead with a Spanish windless and then hang the boat for a few days like a piece of beef to allow the "kinks" to work out of the hull.  Constructing a jig such as the one pictured here gives the builder a lot more control over the out come.

Friday, August 22, 2014

Further pix from Cornwall

Yesterday, Martin Scott teased us with a single photo of his Mistral.  This morning he provided several more pix showing the boat at various stages during construction.


This shot shows us why this type of construction is referred to as "stitch and glue".  One "sews" the two sides of the boat together with either copper wire or nylon zip ties and then pulls the skin panels into shape, usually around the main bulkhead.  Once the shape has been optimized, by locally loosening or tightening wires as required, fiber glass tape wetted out with epoxy resin is laid over the inside of the seams.  Once the resin cures the wires on the external side are trimmed off and an additional layer of glass tape is applied to the outside of the seams.  One can think of the adjustment of the tension on the various wires, to achieve the desired shape, as similar to the process a bicycle mechanic goes through while truing a spoked wheel.

Here, the skin panels have been pulled up around one of the bulkheads.  The ratchet strap is a convenient way to adjust tension while tweaking the the shape before permanently glassing bulkhead in place.

The main bulkhead and center board trunk.  The strips of laminated timber on either side of the trunk help establish the shape of the keel line.  I like the IMCA Moth insignia applied to the bulkhead.  Nice touch.

Copper wire "stitching" along the keel line on either end of the center board trunk.  The prop and shaped piece of wood, like the laminated timbers in the preceding photo help define the shape of the keel's rocker.  Many Mistrals have an awkward knuckle in the bottom aft of the trunk which is created when the skin panels are being tortured into place.  This one will not!

More details of the bracing Martin employed in insure the hull will be twist-free when finished.


The bow after the wires have been cleaned off and the outside layer of glass tape applied.  Hopefully Martin will keep us updated as construction moves along!

Wednesday, August 20, 2014

Meanwhile, down in Cornwall...

A few years ago Martin Scott over in Penzance requested a set of Mistral plans.  We had a bit of bother with the international post but he eventually got them.  Martin was at that time busy with the restoration of a pair of National 12 dinghies and so the Moth, although started, was left on the back burner.  Today Martin sent me a photo of his Mistral hull which he built in a female jig.  She looks quite nice!  Here's what Martin has to say:  "I built it in a female frame jig on the floor and I took it out yesterday to see if will stay straight on its own. Yes its very stable with just a 2mm adjustment on the port gunwale a couple of feet from the bow.  . I should finish the keel tape and resin tomorrow so it can go back in the jig for finishing. I have used Robbins 4mm five ply and should look nice when all varnished. In the above state we are up to 19kg which is not bad as 5 ply is quite heavy. I have eye surgery scheduled for October - notwithstanding all my problems I still hope to have the Moth finished and sailing it in the spring."

Evolution fresh from the jig.  She looks quite sweet.  I hope Martin sends some detailed pix of that building jig.  Most guys pull up the skin panels of a Mistral hull by eye and hence no two Mistrals are ever quite the same!

Thursday, May 22, 2014

John Z's Mistral; May Update

John is working away on his new boat.  There's no rush as he has the old boat as a back up.  His target completion date is to have the new boat ready in time for the Brigantine regatta (14th of June) but that might not happen.  Let's see how he's getting on since our last update.

This photo shows the installation of the side walls of the cockpit buoyancy tanks.  John has opted for slab sided tanks rather than the"rolled" side tanks popularized by Joe Bousquet.  John indicated that a 3mm sheet would take the bend he wanted between the aft cockpit bulkhead and the main forward bulkhead but a 6mm thick panel would not.  Hence the extra clamps and bits of temporary timber bracing while the resin kicked off between the two layers of the tank wall.

John also added ply doublers to the cockpit sole, effectively increasing the thickness from 3mm to 6mm in the "stomping" area of the hull.  Vacuum bagging ensures that there are no resin voids and/or excess resin between the two layers.  John used butyl tape to seal the bag edges against the previously epoxy-coated surface of the hull.

Shaving down the inwhales to the correct angle for the deck.

Adding wood strips to the top faces of the bulkheads and gussets.  These will provide attachment surfaces for the decking.

John coated the inside of the boat with epoxy.  This not only helps preserve the wood but also increases the stiffness of the bendy 3mm ply and thus helps prevent the hull from "oil canning" as it knifes through chop.

I don't know how John keeps his work area so tidy!

One of several gussets which John has added after receiving some input from fellow builder Joe Bousquet.  This one ties the transom to the stern deck brace.

Tuesday, May 14, 2013

John Z's new Moth: progress report

Earlier, I reported on the new Mistral design Moth which John Z has under construction here and here.  Today we get to catch up on John's progress since the last update:

"Here are some photos of the new boat.  I had planned to use a circular arc template as a a guide to make the cambered deck beams; built nice little beams to go alongside of the mast tube and then when I laid a straightedge from the slanted bulkhead to the bow found that my pretty curved beams were a half inch lower than the straightedge.  The circular camber technique works for cruising boats because the sheer line is usually curved upward toward the bow.  On our flat-sheer Mistrals we really want closer to a cone shaped camber for the deck rather than a cylinder so you would need a new template at each station.  I didn't have the heart to tear out the beams and couldn't live with a shoehorn shaped deck so I added shims on top of the beams, determining the shim thickness with a straight edge from the tip of the bow, sweeping an arc over the slanted bulkhead that already had a circular camber."

Live and learn,
John Z
The template for the bulkhead deck crown.

Deck beams to support the mast tube.  John later discovered that they needed a bit of shimming.

Gluing the main bulkhead in place.

Adding shims to those mast tube supports!

Things seem to be shaping up...

Detail pix showing form fitted blocks for the mast tube.

Y2K2 as of 14 May, 2013.